Description
We sell the self-propelled scissor lift table in the Australian area equipped with many safety protection measures, such as overload protection. When the load capacity of the platform exceeds the weight of our presupposition, the platform will not work correctly, and the full-cut cuts have an emergency decline. The function can safely land on the ground in an accident.
As a famous Chinese-famous self-propelled scissor lift table manufacturer, the machine we produce can provide more comfortable, larger load capacity, higher security, complete car manganese steel Q345 material, firm and reliable, shaft pin Self-lubrication system Avoid long-term wear
Maintenance for self-propelled scissor lift table:
The electric self-propelled scissor lift table application is relatively wide. In the case of Australian export cases, it is used in the customer’s factory maintenance, decoration industry, electrical engineering, and other high-altitude operations. If you use the electric scissors lift, you need to work well.
Maintenance and maintenance, to increase the service life of the equipment, reduce accident accidents, and finally increase the frequency of care, can also reduce the risk of risk, and reduce the loss due to fault shutdown.
Using a self-propelled scissor lift table should follow local regulations:
If you import a cutting on scissors from China in Australia, then you should use this machine in accordance with Australia’s laws and regulations, and comply with the relevant standards of the Australian scissor lifts, according to Australian requirements, the daily maintenance Cycle should not exceed 90 days
For battery power electric scissor lift, depending on the model, there are different components and functions, should pay attention to the manual maintenance and maintenance when maintaining, with the correct inspection problem and safety guidance.
Routine maintenance for self-propelled scissor lift table:
- Minor repair of mechanical and electrical systems after 1400 hours of operation; After 4500 hours of operation, carry out intermediate repair of mechanical and electrical systems; After 11000 hours of operation, overhaul the mechanical and electrical systems.
- The brake of each elevator mechanism shall be checked and adjusted frequently to ensure flexibility and reliability. There shall be no dirt on the friction surface. In the case of land, it must be washed off with gasoline or thinner. The lubrication and hydraulic oil of each part shall be carried out according to the requirements in the lubrication table.
- Regularly check whether each mechanism usually operates; at the same time, always check all wires and cables for damage. The damaged parts shall be bound up and replaced in time.
- In case of overheating the motor, stop it in time and continue operating after troubleshooting. The motor bearing shall be well lubricated.
The brush pressure shall be adjusted so that the contact area is not less than 50%. The control box and distribution box shall be kept clean, and the dust on the electrical equipment shall be cleaned in time.
- Check all hydraulic oil pipes and joints of the elevator. The oil pipe shall not be damaged, and the joints shall not be loose. All joints must be tightened. Check the piston rod and transparent plastic vent pipe of the oil cylinder for oil. If there is too much oil, the cylinder’s seals may fail, or the oil tank may be too full.
Self-propelled scissor lift table maintenance knowledge:
1. The scissor lift should open the leg to a certain angle when used and adjust the worksheet to maintain the horizontal state with a hand-rotating screw. Press and hold the rising button lift to rise, reach the working height to loosen the button, indoor and outdoor high-altitude operation users must have a seat belt (safety rope) lift lifting process, strictly forbidden people climb.
2, the scissor lift is not allowed to move, and the four legs are not supported. Overload operations are strictly prohibited during use, and the items contained should be placed appropriately.
3, all hydraulic oil should be kept clean, do not mix with water and other impurities, and usually replaced each year. When maintenance is maintained, or a fault occurs, the power supply should be cut off in time, and the lift should be carried out after raising.
As the primary source of power source, the maintenance and maintenance of the battery is related to the overall service life and efficiency of this scissor lift.
The discharge depth of the battery is much affected by the battery cycle life because the deeper the discharge depth, the more significant the electrode expansion shrinkage, and the more the active substance of the positive electrode are falling off, thereby losing the discharge characteristics and the performance are decreased until the life is terminated. Therefore, the battery should be used to avoid depth discharge, and it should be shallow, and the general situation should be done: the battery is best in charge with a discharge depth of 50% -70%.
The charging current should be less than or equal to the charging current acceptable by the battery. Otherwise, the excess current generated by overcharge will cause the electrolytic water to consume too fast and generate severe precision phenomena, the time is extended, which will make charging very difficult; therefore, when the setting is prevented from being charged as much as possible, to solve this problem, we sell the self-propelled scissor lift table with excessive protection.
Reviews
There are no reviews yet.